Research Blog
How to Prepare a Serial Dilution Series From a Reconstituted Peptide Stock
Published
A worked-example guide to the C1V1=C2V2 math behind building a multi-point serial dilution series for dose-response study design.

For laboratory and research use only. Not for human consumption.
A single reconstituted peptide vial provides one concentration. Many research protocols — particularly dose-response study designs in cell-based or in vitro models — call for a range of concentrations tested in parallel, which means going from one stock solution to a series of progressively diluted working solutions. That process is called a serial dilution, and getting the math right at each step is what keeps the resulting concentration range accurate and reproducible.
This guide walks through the underlying formula, a worked numerical example, and the practical pipetting considerations that make a serial dilution series reliable. It assumes a peptide has already been reconstituted into a stock solution of known concentration — if that step hasn't happened yet, start with our guide to how to reconstitute peptides, step by step.
Key Facts
- A serial dilution creates a sequence of concentrations by diluting each step from the previous one, not from the original stock.
- The governing formula is C1V1 = C2V2, where C is concentration and V is volume.
- Common dilution ratios in research protocols include 1:2 (halving) and 1:10 (log-scale).
- Errors compound across a serial series, so precise volume measurement at each step matters more than in a single dilution.
- Labeling and record-keeping at every step prevents concentration mix-ups later in a study.
The Governing Formula: C1V1 = C2V2
Every dilution step, whether part of a series or a one-off, follows the same conservation-of-mass relationship: the concentration of the stock (C1) multiplied by the volume of stock used (V1) equals the target concentration (C2) multiplied by the final total volume (V2). Rearranged to solve for the volume of stock needed:
V1 = (C2 × V2) ÷ C1
The remaining volume, V2 − V1, is the volume of diluent (typically bacteriostatic or sterile water, depending on the protocol) added to reach the final volume. This single equation is the basis for every step in a serial dilution — the only thing that changes step to step is which concentration is now serving as the "stock" for the next dilution.
Worked Example: A 1:2 Serial Dilution From a 5 mg/mL Stock
Suppose a peptide has been reconstituted to a stock concentration of 5 mg/mL, and a research protocol calls for a five-point 1:2 serial dilution series, each point at a final volume of 1 mL.
Step 1 (Point A): Target concentration 5 mg/mL. This is the stock itself — no dilution needed. Set aside 1 mL directly from the stock.
Step 2 (Point B): Target concentration 2.5 mg/mL. Using C1V1=C2V2 with C1 = 5 mg/mL: V1 = (2.5 × 1) ÷ 5 = 0.5 mL of Point A, combined with 0.5 mL diluent, to make 1 mL at 2.5 mg/mL.
Step 3 (Point C): Target concentration 1.25 mg/mL. Now Point B (2.5 mg/mL) serves as the stock for this step: V1 = (1.25 × 1) ÷ 2.5 = 0.5 mL of Point B, combined with 0.5 mL diluent.
Step 4 (Point D): Target concentration 0.625 mg/mL. Using Point C as the new stock: V1 = (0.625 × 1) ÷ 1.25 = 0.5 mL of Point C, combined with 0.5 mL diluent.
Step 5 (Point E): Target concentration 0.3125 mg/mL. Using Point D as the new stock: V1 = (0.3125 × 1) ÷ 0.625 = 0.5 mL of Point D, combined with 0.5 mL diluent.
The result is a five-point series — 5, 2.5, 1.25, 0.625, and 0.3125 mg/mL — each derived from the point immediately before it, with a constant 1:2 dilution factor throughout. Because each step draws exactly half its volume from the previous point and half from diluent, the ratio stays consistent across the whole series without needing a fresh calculation from the original stock each time.
1:2 vs 1:10 Dilution Series
A 1:2 series (as above) produces a linear halving of concentration at each step, useful when a narrower, more granular concentration range is needed. A 1:10 series, by contrast, drops concentration by one full order of magnitude at each step — useful for scanning a wide concentration range quickly before narrowing in with a finer series around the range of interest. Many dose-response study designs described in the literature use a coarse 1:10 series first, then a follow-up 1:2 series bracketing whatever range produced the response of interest. The choice of ratio is a study-design decision, not a fixed rule — it depends on how much resolution the protocol calls for across the tested range.
Why Errors Compound in a Serial Series
Because each step is diluted from the immediately preceding step rather than from the original stock, any pipetting inaccuracy or calculation error at an early step propagates forward and is amplified at every step downstream. A 5% volume error at Point B in the example above doesn't stay a 5% error — it compounds through Points C, D, and E. This is the single biggest practical difference from a one-off dilution, and it's why calibrated pipettes, consistent mixing technique between steps, and double-checking the arithmetic before starting matter more here than almost anywhere else in a reconstitution workflow. For a quick reference on common mg/mL concentrations before starting a series, see our peptide concentration mg/mL chart.
Labeling and Record-Keeping
Every tube in a serial dilution series should be labeled immediately after it's made — with the compound, the concentration, the date, and the step number — before moving to the next dilution. It is remarkably easy to lose track of which tube is which partway through a five- or ten-point series, and an unlabeled or mislabeled tube effectively invalidates that data point. Keeping a written or digital log alongside the physical tubes, recording the exact volumes used at each step (not just the target), also makes it possible to retrace and verify the series later if a result looks unexpected.
Starting From an Accurate Stock Concentration
None of the serial dilution math above is meaningful if the starting stock concentration itself is wrong. That concentration is set at the reconstitution step — mg of peptide divided by mL of diluent added — and it's worth double-checking before building a dilution series on top of it. Our reconstitution calculator handles that starting calculation, and our worked walkthrough of BPC-157 reconstitution mg-to-mL concentration math shows the same underlying arithmetic applied to a single-vial example.
FAQ
What is the C1V1=C2V2 formula used for?
C1V1=C2V2 is the standard dilution equation relating a stock's concentration (C1) and volume used (V1) to a target concentration (C2) and final volume (V2). It is used to calculate how much stock solution and diluent to combine to reach a specific target concentration.
What is the difference between a serial dilution and a single dilution?
A single dilution produces one target concentration directly from a stock. A serial dilution produces a sequence of progressively lower concentrations by diluting each step from the previous one rather than from the original stock, commonly used to generate a concentration range for dose-response study design.
What dilution ratios are commonly used in a serial dilution series?
Common ratios reported in research protocols include 1:2 (halving the concentration at each step) and 1:10 (log-scale steps). The choice depends on how fine a concentration gradient the study design calls for across the range being tested.
Why does dilution accuracy compound across a serial dilution series?
Because each step in a serial dilution is diluted from the previous step rather than from the original stock, a pipetting or calculation error at any point carries forward and is amplified at every subsequent step, which is why precise volume measurement matters more in a serial series than in a single dilution.
For laboratory and research use only. Not for human consumption.